Bush Removal & Installation

A universal system for the removal and installation of Suspension Bushes, Bearings, Seals etcBy selecting the appropriate diameter sleeves, the bush / bearing / seal is Pressed or Pulled by the action of turning the spindle nuts in opposing directions.Fully universal applications for Cars, LCVs HGVs etc, with a range of kit options to suit individual requirements.Press & Pull Sleeve Kits can be used in the following formats: As a stand alone set of tools With a standard workshop press With a Universal Press Frame (187000V2) With a Universal C Clamp (18780200) Can also be used with selected model specific Press Piece sets and in conjunction with optional hydraulic upgrade kits All components are available individually as spare parts, for full list of spare parts please see spare parts section or instructions in the downloads section. Universal applications - Car - LCV Contains 20x Press Sleeves in 2mm diameter steps Inside Diameter Range: 34 - 72mm Outside Diameter Range: 44 - 82mm 4x Step Plates / 4x Pulling Spindles with thrust bearings Supplied in moulded storage case

Read more less

For use as an add-on to the Standard Press & Pull Sleeve Kit (08780000) Allows access to a wider range of vehicles, particularly SUVs and LCVs Contains 8 x Press Sleeves in 2mm diameter steps Inside Diameter Range: 82 - 88mm and 98 - 104mm Outside Diameter Range: 92 - 98mm and 108 - 114mm 4 x Step Plate Discs 2 x 20mm Pulling Spindle Adaptors with Thrust Bearings M20 Supplied in moulded storage case All components are available individually as spare parts, for full list of spare parts please see spare parts section or instructions in the downloads section.

Read more less

A universal system for the removal and installation of Suspension Bushes, Bearings, Seals etcBy selecting the appropriate diameter sleeves, the bush / bearing / seal is ˜Pressed, or ˜Pulled by the action of turning the spindle nuts in opposing directions.Fully universal applications for Cars, LCVs HGVs etc, with a range of kit options to suit individual requirements. Press & Pull Sleeve Kits can be used in the following formats: As a stand alone set of tools With a standard workshop press With a Universal Press Frame (187000V2) With a Universal C Clamp (18780200) Can also be used with selected model specific Press Piece sets and in conjunction with optional hydraulic upgrade kits Complete kit for SUV, LCV, PSV, HGV Contains 20x Press Sleeves in 2mm diameter steps Inside Diameter Range: 74 - 112mm in 2mm steps Outside Diameter Range: 84 - 122mm in 2mm steps 4x Step Plate Discs / 4x Pulling Spindles with nuts & thrust bearings M10 / M12 / M14 / M16 2 x 20mm Heavy Duty Pulling Spindles (M20 long & M20 short) with thrust bearings Supplied in moulded storage case All components are available individually as spare parts, for full list of spare parts please see spare parts section or instructions in the downloads section.

Read more less

For the removal and installation of suspension bushes, ball joints, bearings, seals etc By selecting the appropriate diameter sleeves, the component is ˜pressed, or ˜pulled by the action of turning the spindle nuts in opposing directions Contains: 10 x Press Sleeves in 2mm diameter steps Inside Diameter Range: 14 - 32mm Outside Diameter Range: 24 - 42mm Includes 2 x spindles, 4 x stepped back plates, extension spindle with thrust bearing, lock nuts and grease Supplied in moulded storage case

Read more less

Upgrade kit from 08790000 to complete 08797500 For owners of the XL basic kit 08790000 (SUV / LCV) who wish to upgrade to the full contents of the XL Comprehensive Kit (08797500) All components are available individually as spare parts, for full list of spare parts please see spare parts section or instructions in the downloads section.

Read more less

Land Rover Discovery 3 & 4 Suspension Bush Rear Upper KitA comprehensive solution specifically designed for removal of seized / corroded bushes and installation of replacement bushes for Land Rover Discovery 3/4 and Range Rover Sport modelsAvailable kits are as follows:- Master Kit (18777000)- Front lower (18777100)- Front upper (18777200)- Rear lower (18777300)- Rear upper (18777400) Only the bushes have to be replaced, saving the cost and time in replacing the complete arm Lower arm bushes can be replaced on vehicle without having to remove the wheel Individual press frame pieces for each wishbone To be used in conjunction with the SP Universal Press Frame (18700100) and due to the nature of corroded components, the power of the SP 12 Tonne Hydraulic Ram is also required (18000000) (Can be purchased together as 187000V2 - Universal Press Frame c/w 12 Tonne Hydraulic Ram) The SP 90206000 Vibro Impact Air Hammer and SP 96020000 Induction Heater can be used to assist in the removal of corroded suspension bolts and bushes - See video below

Read more less

Land Rover Discovery 3 & 4 Suspension Bush Rear Lower KitA comprehensive solution specifically designed for removal of seized / corroded bushes and installation of replacement bushes for Land Rover Discovery 3/4 and Range Rover Sport modelsAvailable kits are as follows:- Master Kit (18777000)- Front lower (18777100)- Front upper (18777200)- Rear lower (18777300)- Rear upper (18777400) Only the bushes have to be replaced, saving the cost and time in replacing the complete arm Lower arm bushes can be replaced on vehicle without having to remove the wheel Individual press frame pieces for each wishbone To be used in conjunction with the SP Universal Press Frame (18700100) and due to the nature of corroded components, the power of the SP 12 Tonne Hydraulic Ram is also required (18000000) (Can be purchased together as 187000V2 - Universal Press Frame c/w 12 Tonne Hydraulic Ram) The SP 90206000 Vibro Impact Air Hammer and SP 96020000 Induction Heater can be used to assist in the removal of corroded suspension bolts and bushes - See video below

Read more less

Land Rover Discovery 3 & 4 Suspension Bush Front Upper KitA comprehensive solution specifically designed for removal of seized / corroded bushes and installation of replacement bushes for Land Rover Discovery 3/4 and Range Rover Sport modelsAvailable kits are as follows:- Master Kit (18777000)- Front lower (18777100)- Front upper (18777200)- Rear lower (18777300)- Rear upper (18777400) Only the bushes have to be replaced, saving the cost and time in replacing the complete arm Lower arm bushes can be replaced on vehicle without having to remove the wheel Individual press frame pieces for each wishbone To be used in conjunction with the SP Universal Press Frame (18700100) and due to the nature of corroded components, the power of the SP 12 Tonne Hydraulic Ram is also required (18000000) (Can be purchased together as 187000V2 - Universal Press Frame c/w 12 Tonne Hydraulic Ram) The SP 90206000 Vibro Impact Air Hammer and SP 96020000 Induction Heater can be used to assist in the removal of corroded suspension bolts and bushes - See video below

Read more less

For driving out components and straightening jobs on bodywork with extra tough heavy-duty design and practical handles 8 tonne (approx.) maximum force Loosens even the tightest connections; pressed or rusted in / attached with a cone Suitable for removing injectors, wheel hubs, supporting joints etc. with relevant accessories Specifications: Weight: 9kg Length: 770mm Connection Thread: M18 x 1.5

Read more less

For use with GO520 & GO530 Heavy Duty Suspension Hook for use with slide hammers when repairing axles and bodywork Ideal for loosening connections on the oscillating trapezoidal arm (ball joint / tightening hole) and on the wheel bearing housing with the spring struts inserted Also ideal for straightening work on columns A, B or C due to the bracket profile   Technical data:  Connection thread: M18x1.5  Internal height: 110 mm  Hook Width: 40 mm  Total weight: 2.34 kg   Applications Include Ford Mondeo, Mercedes-Benz Vito front axle etc. 

Read more less

For use with GO520 & GO530 Universal slide hammer use when paired with GO522 M18 x 1.5 adaptor Compatible with 10mm steel chains Special hook design provides reliable fitting High-quality hardened and tempered steel construction Includes mounting bolts

Read more less

For use with GO520 & GO530 Universal slide hammer use when paired with GO522 M18 x 1.5 adaptor Special hook design provides reliable fitting High-quality hardened and tempered steel construction Universal adaptation on each chain end, independent of manufacturing and for tension brackets with notch cone/ conical collar No twisting of chain during turning and rehanging Includes mounting bolts

Read more less

For use with GO520 & GO530 System adapter tool with mounting bore (jointed connection) for universal hooks/double extractor hooks/bow hooks/bodywork pull clamps etc. Allows GO526 and GO527  to be used with slide hammers

Read more less

Adaptor Set for Heavy Duty Slide Hammer Supplied with 4 x commonly used slide hammer adaptors  1 x system adaptor tool, M18 x 1.5 with mounting bore (jointed connection) for universal hooks, double extractor hooks, bow hooks, bodywork pull clamps etc. Suitable for Muller /Klann /KS /Pichler 1 x system adaptor tool, M18x1.5/1-1/2 inch x 16 for wheel hub puller. Suitable for Muller /KS /Pichler 1 x universal adaptor with ball joint, M18x1.5, for use between the slide hammer and the tool, enables work in hard-to-reach places. Suitable for all systems 1 x system adaptor tool, M18 x 1.5/M22x2.0, for wheel hub puller. Suitable for Facom

Read more less

For use with GO101 in combination with transmission jacks from other manufacturers The lifts stem is not damaged thanks to the plastic finish of the adaptors Adaptor sizes: Ø25.5mm, Ø30.5mm & Ø35.5mm   Components: 1 x adaptor size 1 - outside Ø 40mm for Ø 25mm stem, Length 50mm 1 x adaptor size 2 - outside Ø 40mm for Ø 30mm stem, Length 50mm 1 x adaptor size 3 - outside Ø 40mm for Ø 35mm stem, Length 50mm

Read more less

When used in conjunction with components from 08780000, or 08797500, these kits allow application of up to 12 tons of hydraulic force which can be used to provide a controlled force in place of the manual or mechanical effort required when using 08780000 / 08797500 Contents: - Hollow Ram Hydraulic Cylinder, Alignment washer and 2x extra-long heavy-duty spindles that are rated for use with the hydraulic ram. (Note: Standard 08780000 spindles are not rated for use with the 18782500 and / or 18792500 hydraulic ram) Cylinder: 40mm stroke

Read more less

A universal system for the removal and installation of Suspension Bushes, Bearings, Seals etc By selecting the appropriate diameter sleeves, the bush / bearing / seal is ˜Pressed, or ˜Pulled by the action of turning the spindle nuts in opposing directions. Fully universal applications for Cars, LCVs HGVs etc, with a range of kit options to suit individual requirements. Press & Pull Sleeve Kits can be used in the following formats: As a stand alone set of tools With a standard workshop press With a Universal Press Frame (187000V2) With a Universal C Clamp (18780200) Can also be used with selected model specific Press Piece sets and in conjunction with optional hydraulic upgrade kits All components are available individually as spare parts   When used in conjunction with components from 08780000, or 08797500, these kits allow application of up to 12 tons of hydraulic force which can be used to provide a controlled force in place of the manual or mechanical effort required when using 08780000 / 08797500 Contents: - Hollow Ram Hydraulic Cylinder, Alignment washer and 2x extra-long heavy-duty spindles that are rated for use with the hydraulic ram. (Note: Standard 08780000 spindles are not rated for use with the 18782500 and / or 18792500 hydraulic ram) Cylinder: 8mm stroke

Read more less

For the dismantling / installation of suspension components on the vehicle Jaw opening: 245mm Throat depth: 100mm Includes adaptors for use with the 08780000 and XS Sleeve kits Designed to allow greater access in restricted situations and where the universal press frame is not suitable Special trapezoidal threaded screw, allows for the application of greater force Base cup works with gold and silver rings from the SP press frame (18700100 / 187000V2) Includes impact screw which can be removed and replaced with a hydraulic ram (1500 & 1800 Series) Can be used with an impact gun

Read more less

Universal clamps for the dismantling and installation of suspension parts on the vehicle Specially designed Universal Clamps for use with the '0878 / '0879 Series Press & Pull Sleeve Kits Designed to allow greater access in restricted situations and where the Universal Press Frame is not suitable Special trapezoidal threaded screw, allows for the application of greater force and can be used with Impact Air Wrenches, as well as standard ratchets / wrenches etc. Also capable of accepting the SP1500 or SP1800 Hydraulic Rams.  Internal frame dimensions: 245mm x 70mm

Read more less

A comprehensive solution specifically designed for removal of seized / corroded bushes and installation of replacement bushes for Land Rover Discovery 3/4 and Range Rover Sport modelsAvailable kits are as follows:- Master Kit (18777000)- Front lower (18777100)- Front upper (18777200)- Rear lower (18777300)- Rear upper (18777400) Only the bushes have to be replaced, saving the cost and time in replacing the complete arm Lower arm bushes can be replaced on vehicle without having to remove the wheel Individual press frame pieces for each wishbone To be used in conjunction with the SP Universal Press Frame (18700100) and due to the nature of corroded components, the power of the SP 12 Tonne Hydraulic Ram is also required (18000000) (Can be purchased together as 187000V2 - Universal Press Frame c/w 12 Tonne Hydraulic Ram) The SP 90206000 Vibro Impact Air Hammer and SP 96020000 Induction Heater can be used to assist in the removal of corroded suspension bolts and bushes - See video 

Read more less

Sykes-Pickavant have developed a solution for the efficient removal and refitting of bushes on traditional Land Rover models For radius arm, panhard bushes and general suspension bushes Dedicated shaped press pieces for correct location and alignment Suitable for Land Rover Models: Defender, Discovery 1 & 2, Classic Range Rover, Range Rover P38A & older Series Land Rovers Kit includes 6 Piece Adaptor Set, 18775100 step plate & C Clamp for minimal vehicle strip-down 

Read more less

Sykes-Pickavant have developed a solution for the efficient removal and refitting of bushes on traditional Land Rover models For radius arm, panhard bushes and general suspension bushes Dedicated shaped press pieces for correct location and alignment Suitable for Land Rover Models: Defender, Discovery 1 & 2, Classic Range Rover, Range Rover P38A & older Series Land Rovers Kit includes 6 Piece Adaptor Set, 18775100 step plate, press frame & adaptor ring, for customers who already have an SP hydraulic ram*Note - With certain large radius arm bushes, the adaptor pieces can still be used with a workshop press or C Clamp 

Read more less

Sykes-Pickavant have developed a solution for the efficient removal and refitting of bushes on traditional Land Rover models For radius arm, panhard bushes and general suspension bushes Dedicated shaped press pieces for correct location and alignment Suitable for Land Rover Models: Defender, Discovery 1 & 2, Classic Range Rover, Range Rover P38A & older Series Land Rovers Kit includes 6 Piece Adaptor Set, 18775100 step plate, press frame, adaptor ring & 12 Tonne SP hydraulic ram*Note - With certain large radius arm bushes, the adaptor pieces can still be used with a workshop press or C Clamp 

Read more less

New single piece stepped press frame plate Allows for many different sized press pieces to fit positively into the frame for precise work

Read more less

Sykes-Pickavant have developed a solution for the efficient removal and refitting of bushes on traditional Land Rover models For radius arm, panhard bushes and general suspension bushes Dedicated shaped press pieces for correct location and alignment Suitable for Land Rover Models: Defender, Discovery 1 & 2, Classic Range Rover, Range Rover P38A & older Series Land Rovers Kit includes 6 Adaptor Pieces for use in a workshop press with suspension parts removed from vehicle

Read more less

A new on vehicle solution for the removal and replacement of twin swivel ball joints as fitted onto the front axles of two popular Land Rover models: Discovery 2 1998 “ 2004 & Range Rover P38A 1994 - 2002 Uses the Sykes-Pickavant 187 Hydraulic Series press frame to deliver 12 tonnes of force, for a "take the press" to the car solution (Inc in 18771100 only) Designed, tested and manufactured in Great BritainOther kit options available - See related products 18771100 and 18771200

Read more less

For the removal and installation of lower ball joints as fitted to the following:- Nissan Interstar 02 onwards- Opel Movano 98 onwards- Renault Master II 98 onwards Adaptors can be used in a press frame with a hydraulic ram 

Read more less

For the removal and installation of upper ball joints as fitted to the following:- Nissan Interstar ˜02 onwards- Opel Movano ˜98 onwards- Renault Master II ˜98 onwardsAdaptors can be used in a press frame with a hydraulic ram

Read more less

Adaptors can be used in a press frame with either a 12731100 pressure screw (recommended) or a hydraulic ramKit includes adaptor set for Focus Bushes, for the removal and installation of trailing arm bushesFocus Bush OEM reference numbers: 1 061 670, 1304124Focus Applications:- C-MAX ˜07- MPV- MKI ˜98-04 Estate, Hatchback, Saloon, Van- MKII ˜04- Convertible, Hatchback, Saloon, Van- Kuga ˜08- Off Road- Mazda 3 (BK) ˜03-09 Saloon, Hatchback- Mazda 5 (CR/CW) ˜05- MPV- Volvo C30 ˜06- Hatchback- Volvo C70 II ˜07- Cabrio- Volvo S40 II ˜04-12 Saloon- Volvo V50 ˜04-12 Estate*Note - Adaptor Ring 18780400 required

Read more less

Adaptors can be used in a press frame with either a 12731100 pressure screw (recommended) or a hydraulic ramKit includes adaptor set for Fiesta Bushes, for the removal and installation of trailing arm bushesFiesta Bush OEM reference numbers: 1011363, 1016439, 96FB5K653CAFiesta Applications:- Fiesta ˜95-02- KA ˜96-08- Puma ˜96-02*Note - Adaptor Ring 18780400 required

Read more less

Includes adaptor ring (18780400) for use with 08780000 and related press piece sets Can also be used with 8 or 12 Tonne SP hydraulic ram and press frame pressure screw   Also available without adaptor ring as part number 18700170

Read more less

Updated unit now provides greater power Allows easier operation - 50% more capable using the SP 12 tonne Hydraulic Ram Includes adaptor ring for use with 08780000 Universal Press & Pull Sleeve Kit Can be used in the following formats:- On its own as a stand alone tool- With Universal Press & Pull sleeve kits Open frame design - 200mm of clearance through the press frame Ideal for use with individual model specific press piece sets

Read more less

SAF Pivot Bush Installation and Removal Tool For use on SAF Axle Pivot Eye Bush for IU or IO IDP Intradisc Plus & Integral Axles The 3D bush is an integral component that is pressed into the suspension arm to absorb wheel, side tilt and braking forces for greatly increased handling and stability Easily remove and install SAF pivot bushes with the aid of an impact wrench No separate tool needed for removal of the old bushes 4.177.3028.00 3D pivot bush Merc Discos axle bush part number JAE3020500250 Meritor CS9i axle bush part number 21230041

Read more less

For the installation and removal of the rear axle body mounting bush found on Fiesta Mark VI 2008 onwards Fiesta Bush Number: 1805815 (FEB34748)

Read more less

NEW on-car solutionNow capable of installing & removing the longer bush as fitted onto the nearside of recent Volvo cars  Individual press piece kit for dismantling and installing the rear wishbone / trailing arm bush Correctly aligns & sets bush depth in trailing arm upon installation, so not to tear bush Suitable for: Ford: Mondeo ˜07- / Mondeo Estate ˜07- / S-Max & Galaxy ˜06- Volvo: XC70 & V70 ˜07- / XC60 ˜08- / S60 & V60 ˜10-

Read more less

To remove and install the rear axle body bush on the vehicle Suitable for: - Astra H 2004 onwards - Meriva B 2010 onwards - Zafira B 2005 onwards Astra Bush Number: 13267215 (FSK7164)

Read more less

For the removal and replacement of the large rear bush on the lower arms of Ford Transits from 2000 “ 2013 Designed to be used with a 187000V2 press frame and ram On vehicle solution with minimal strip down Can also be used in a workshop press for lower arms when they have been removed from the vehicle Applications: Ford Transit Mk5 & Mk6 from 2000 to 2013 OE Bush Numbers covered: 4042024, 4372132, 4540787 & 7372131   

Read more less

Spindle pack suitable for use with: 08780000 - Universal Press & Pull Sleeve Kit 08785500 - XS Sleeve Kit - Basic 08786500 - XS Sleeve Kit - Master 08790000 - XL Sleeve Kit - Basic 08797500 - XL Sleeve Kit - Comprehensive Generates greater power than standard spindlesWorks with standard spindles and increases lifespanSquare profile heavy duty pulling threadLarge surface area roller bearing for greater delivery of powerContents: Counter Nut M10 Counter Nut M12 Counter Nut M14 Nut TR20 with bearing Spindle TR20 - Short Spindle TR20 - Long

Read more less

Heavy Duty M16 430mm Threaded Rod and Alignment Washer

Read more less

Heavy Duty M14 430mm Threaded Rod and Alignment Washer

Read more less

Spindle pack suitable for use with: 08780000 - Universal Press & Pull Sleeve Kit 08785500 - XS Sleeve Kit - Basic 08786500 - XS Sleeve Kit - Master 08790000 - XL Sleeve Kit - Basic 08797500 - XL Sleeve Kit - Comprehensive Generates greater power than standard spindlesWorks with standard spindles and increases lifespanSquare profile heavy duty pulling threadLarge surface area roller bearing for greater delivery of powerContents: Counter Nut M10 Counter Nut M12 Counter Nut M14 Nut TR20 with bearing Spindle TR20 - Short 

Read more less

Spindle pack suitable for use with:08780000 - Universal Press & Pull Sleeve Kit 08785500 - XS Sleeve Kit - Basic08786500 - XS Sleeve Kit - Master 08790000 - XL Sleeve Kit - Basic08797500 - XL Sleeve Kit - ComprehensiveGenerates greater power than standard spindlesWorks with standard spindles and increases lifespanSquare profile heavy duty pulling threadLarge surface area roller bearing for greater delivery of powerContents: Counter Nut M10 Counter Nut M12 Counter Nut M14 Nut TR20 with bearing Spindle TR20 - Long

Read more less

Ring sits in press frame to hold adaptors in place

Read more less

New kit designed for use with the 0878 range of sleeve kits Extends the 187 press frame - internal capacity from 200 to 350mm Pair of 150mm legs fit onto original 187 press frame legs Nose piece connects press frame ram with 4 x step plate discs from the 0878range of sleeve kits

Read more less

Kit includes adaptor set for the removal and installation of trailing arm bushes, 18700100 Press Frame and 18704100 Pressure ScrewBush OEM reference numbers: Fiesta: 1011363, 1016439, 96FB5K653CA Focus: 1 061 670, 1304124  Focus Applications: C-MAX ˜07- MPV MKI ˜98-04 Estate, Hatchback, Saloon, Van MKII ˜04- Convertible, Hatchback, Saloon, Van Kuga ˜08- Off Road Mazda 3 (BK) ˜03-09 Saloon, Hatchback Mazda 5 (CR/CW) ˜05- MPV Volvo C30 ˜06- Hatchback Volvo C70 II ˜07- Cabrio Volvo S40 II ˜04-12 Saloon Volvo V50 ˜04-12 Estate Fiesta Applications: Fiesta ˜95-02 KA ˜96-08 Puma ˜96-02

Read more less

Use this tool kit to remove and refit slotted bushes properly. The slight conical grinding makes it possible to extract and reuse bushes without damage. The tools may be fit directly on the vehicle without removing entire axes components. Pressers may also be used on the workshop press. By means of the locking device and relating half-shells, bushes are pre-tensioned carefully and parallel to one another so they can be pressed easily into their seat. While the bush is often damaged using commercial tapered sockets, the assembly operations do not damage/deform/detach the bearing's cover when this locking device system is used. The half-shells are fixed securely inside the locking device so they will not slip out. The kit includes a wide selection of the most common applications with high market coverage. Other half-shell kits will soon follow to ensure the subsequent removal of the system. Due to the partly enormous forces required especially for removal, the use of a hydraulic cylinder is recommended. The Govoni 12-ton hydraulic cylinder is therefore optimal for integrations.  (See kit GO1310R to purchase with the GO1012 Hydraulic Cylinder) Application Ø 75mm MB Actros (stabilizer) Ø 70mm MAN Ø 68mm MAN (front spring) ROR, SAF Ø 66mm IVECO Eurostar (driver’s cabin) Ø 65mm MB Actros (stabilizer), Atego Ø 63mm DAF Ø 60mm MB/IVECO Eurostar (stabilizer), Renault Kerax, Magnum, Premium (leaf spring eye) Ø 58mm MB 3229 B, 652, 650/Volvo Ø 56mm IVECO Eurostar (driver’s cabin)

Read more less

For the removal and installation of split / spring eye bushes on HGV vehicles Uses a unique clamping system and a series of shells for a range of bush sizes from 56mm Dia to 75mm Dia. Allows the operator to work in a limited access environment and so reduce the amount of disassembly work required Comprehensive kit includes clamp assembly, 9 x shells - 56mm / 58mm / 60mm / 63mm / 65mm / 66mm / 68mm / 70mm / 75mm plus hydraulic componentsApplications:Mercedes Benz, MAN, MAN Front Spring, IVECO Eurostar, Mercedes Benz Actros, Atego, DAF and Volvo 20017000 Hand Operated Hydraulic Aluminium Pump is required in order to operate the kit

Read more less

For the removal and installation of split / spring eye bushes on HGV vehicles Uses a unique clamping system and 2 x sets of shells for MB & DAF (63mm and 75mm) When used with a hydraulic pump (20017000/20017500) the kit allows the operator to work in a limited access environment and so reduce the amount of disassembly work required Includes clamp assembly, 2 x shells - 63mm and 75mm plus hydraulic components Applications:Mercedes Benz, Mercedes Benz Actros / Atego and DAF

Read more less